8990
卡特330C挖掘機故障代碼中英對照表
2018/8/11
Engine Control發動機控制器(MID No.036)挖掘機維修,挖掘機修理,維修挖掘機,修理挖掘機|CIDComponent元件
0001 Injector Solenoid 1st Cylinder1#缸噴油器電磁閥
0002 Injector Solenoid 2nd Cylinder2#缸噴油器電磁閥
0003 Injector Solenoid 3rd Cylinder3#缸噴油器電磁閥
0004 Injector Solenoid 4th Cylinder4#缸噴油器電磁閥
0005 Injector Solenoid 5th Cylinder5#缸噴油器電磁閥
0006 Injector Solenoid 6th Cylinder6#缸噴油器電磁閥
0041 8V DC Supply 8V直流電源
0042 Injection Actuation Control Valve噴油器促動控制閥
0091 Throttle Position Signal油門位置信號
0094 Fuel Pressure Sensor燃油壓力國傳感器
0100 Engine Oil Pressure Sensor發動機機油壓力傳感器
0110 Engine Coolant Temperature Sensor發動機冷卻液溫度傳感器
0164 Injector Actuation Pressure噴油器促動壓力
0168 System Voltage 系統電壓
0172 Intake Manifold Air Temperature進氣岐管空氣溫度
0175 Engine Oil Temperature Sensor發動機機油溫度傳感器
0190 Engine Speed Sensor發動機速度傳感器
0253 Personality Module 個性模塊
0261 Engine Timing Calibration發動機正時校驗
0262 5V Sensor DC Power Supply5V傳感器直流電源
0268 Check Programable Parameters檢查可編程參數
0273 Turbo Outlet Pressure Sensor渦輪增壓器出口壓力傳感器
0274 Atmospheric Pressure Sensor大氣壓力傳感器
0286 Oil Lamp機油燈
0342 Secondary Engine Speed Sensor次級發動機速度傳感器
0617 Air Inlet Heater Relay空氣進氣加熱繼電器
1627 Fuel Pump Relay燃油泵繼電器Engine / Pump Control發動機/泵控制器(MID No. 105)CID Component元件
0091 Throttle Position Signal油門位置信號
0096 Fuel Level Sensor燃油油位傳感器
0110 Engine Coolant Temperature Sensor發動機冷卻液溫度傳感器
0167 Alternator發電機
0168 Voltage Of The Power Supply (Keyswitch) 鑰匙門電壓
0190 Speed Sensor速度傳感器
0248 Cat Data LinkCAT數據線
0286 Signal For Low Engine Oil Pressure發動機機油壓力低信號
0374 Swing Brake Solenoid回轉制動電磁閥
0376 Travel Alarm 行走警報
0581 "Proportional Reducing Valve For The Powershift Pressure"動力換檔比例減壓閥
0586 Engine Speed Dial發動機速度盤式開關
0587 Feedback Sensor For The Governor Actuator調節器傳動裝置反饋信號
0590 Engine Controller發動機控制器
0598 Travel Speed Solenoid行走速度電磁閥
0600 Hydraulic Oil Temperature Sensor液壓油溫傳感器
1161 Pump Delivery Pressure泵壓
1162 Pump Delivery Pressure泵壓
1524 "Proportional Solenoid Valve ForNegative Flow Control"負流量控制比例電磁閥1525Straight Travel Solenoid直線行走電磁閥1590"Proportional Solenoid Valve ForNegative Flow Control" 負流量控制比例電磁閥2002Action Alarm警報FMI故障描述
0 Data valid but above normal operationl range數據正確，但高于正常范圍
1 Data valid but below normal operationl range數據正確，但低于正常范圍
2 Data erratic,intermittent ,or incorrect數據不穩，斷續或不正確
3 Voltage above normal or shorted high電壓高于正?；蛲蝗桓?/span>
4 Voltage below normal or shorted low電壓低于正常或突然低
5 Current below normal or open circuit電流低于正?；蜷_路
6 Current above normal or grounded circuit電流高于正常或短路
7 Mechanical system not responding properly機器系統沒有正確反應
8 Abnormal frequency, pulse width, or period.異常頻率、脈沖或周期
9 Abnormal update.異常更新
10 Abnormal rate of change.異常變化率
11 Failure mode not identifiable.故障模式不能確認
12 Bad device or component.壞的設備或元件
13 Out of calibration.超出校驗范圍
14-31 Reserved保留事件代碼Event Codes事件代碼Engine / Pump Control發動機/泵控制器Event Code Condition
017 Coolant Overheat冷卻液高溫
043 "Abnormal Battery Charge(Voltage To Power Supply Low)" 電壓異常（電壓低）
050 "Abnormal Battery Charge(Voltage To Power Supply High)" 電壓異常（電壓高）
059 Insufficient Level Of Coolant冷卻液不足
095 Fuel Filter Is Clogged燃油濾芯堵塞
100 Engine Oil Pressure Is Low發動機機油壓力低
119 Fuel Level Is Low燃油油位低
171 Engine Oil Level Is Low發動機機油油位低
179 "Abnormal Battery Charge(Charging Is Abnormal)" 電瓶充電異常
232 Water Separator Draining Demand油水分離器需排水
235 Hydraulic Oil Level Is Low液壓油位低
236 Hydraulic Oil Filter Is Clogged液壓油濾芯堵塞
237 Overload Warning過載警報
272 Air Filter Is Clogged空氣濾芯堵塞
600 Hydraulic Oil Overheat液壓油高溫
862 Special Filter Is Clogged專用濾芯堵塞
863 Automatic Greasing Failure油脂自動注油失敗Event Codes事件代碼Engine Control發動機控制器Event CodeCondition
005 Fuel Filter Restriction Derate燃油濾芯堵塞減額
015 High Engine Coolant Temperature Derate冷卻液高溫減額
017 High Engine Coolant Temperature Warning冷卻液高溫警報
025 High Inlet Air Temperature Derate進氣溫度高減額
027 High Inlet Air Temperature Warning進氣溫度高警報
039 Low Engine Oil Pressure Derate機油壓力低減額
096 High Fuel Pressure燃油壓力高
100 Low Engine Oil Pressure Warning發動機機油壓力低警報
190 Engine Overspeed Warning發動機超速警報
265 User Defined Shutdown用戶自定義熄火挖掘機技術故障與師傅進行溝通交流，官方網站http://www.ccooddee.com修理直撥:0551-64493367 服務專線:13956953738
0001 Injector Solenoid 1st Cylinder1#缸噴油器電磁閥
0002 Injector Solenoid 2nd Cylinder2#缸噴油器電磁閥
0003 Injector Solenoid 3rd Cylinder3#缸噴油器電磁閥
0004 Injector Solenoid 4th Cylinder4#缸噴油器電磁閥
0005 Injector Solenoid 5th Cylinder5#缸噴油器電磁閥
0006 Injector Solenoid 6th Cylinder6#缸噴油器電磁閥
0041 8V DC Supply 8V直流電源
0042 Injection Actuation Control Valve噴油器促動控制閥
0091 Throttle Position Signal油門位置信號
0094 Fuel Pressure Sensor燃油壓力國傳感器
0100 Engine Oil Pressure Sensor發動機機油壓力傳感器
0110 Engine Coolant Temperature Sensor發動機冷卻液溫度傳感器
0164 Injector Actuation Pressure噴油器促動壓力
0168 System Voltage 系統電壓
0172 Intake Manifold Air Temperature進氣岐管空氣溫度
0175 Engine Oil Temperature Sensor發動機機油溫度傳感器
0190 Engine Speed Sensor發動機速度傳感器
0253 Personality Module 個性模塊
0261 Engine Timing Calibration發動機正時校驗
0262 5V Sensor DC Power Supply5V傳感器直流電源
0268 Check Programable Parameters檢查可編程參數
0273 Turbo Outlet Pressure Sensor渦輪增壓器出口壓力傳感器
0274 Atmospheric Pressure Sensor大氣壓力傳感器
0286 Oil Lamp機油燈
0342 Secondary Engine Speed Sensor次級發動機速度傳感器
0617 Air Inlet Heater Relay空氣進氣加熱繼電器
1627 Fuel Pump Relay燃油泵繼電器Engine / Pump Control發動機/泵控制器(MID No. 105)CID Component元件
0091 Throttle Position Signal油門位置信號
0096 Fuel Level Sensor燃油油位傳感器
0110 Engine Coolant Temperature Sensor發動機冷卻液溫度傳感器
0167 Alternator發電機
0168 Voltage Of The Power Supply (Keyswitch) 鑰匙門電壓
0190 Speed Sensor速度傳感器
0248 Cat Data LinkCAT數據線
0286 Signal For Low Engine Oil Pressure發動機機油壓力低信號
0374 Swing Brake Solenoid回轉制動電磁閥
0376 Travel Alarm 行走警報
0581 "Proportional Reducing Valve For The Powershift Pressure"動力換檔比例減壓閥
0586 Engine Speed Dial發動機速度盤式開關
0587 Feedback Sensor For The Governor Actuator調節器傳動裝置反饋信號
0590 Engine Controller發動機控制器
0598 Travel Speed Solenoid行走速度電磁閥
0600 Hydraulic Oil Temperature Sensor液壓油溫傳感器
1161 Pump Delivery Pressure泵壓
1162 Pump Delivery Pressure泵壓
1524 "Proportional Solenoid Valve ForNegative Flow Control"負流量控制比例電磁閥1525Straight Travel Solenoid直線行走電磁閥1590"Proportional Solenoid Valve ForNegative Flow Control" 負流量控制比例電磁閥2002Action Alarm警報FMI故障描述
0 Data valid but above normal operationl range數據正確，但高于正常范圍
1 Data valid but below normal operationl range數據正確，但低于正常范圍
2 Data erratic,intermittent ,or incorrect數據不穩，斷續或不正確
3 Voltage above normal or shorted high電壓高于正?；蛲蝗桓?/span>
4 Voltage below normal or shorted low電壓低于正常或突然低
5 Current below normal or open circuit電流低于正?；蜷_路
6 Current above normal or grounded circuit電流高于正常或短路
7 Mechanical system not responding properly機器系統沒有正確反應
8 Abnormal frequency, pulse width, or period.異常頻率、脈沖或周期
9 Abnormal update.異常更新
10 Abnormal rate of change.異常變化率
11 Failure mode not identifiable.故障模式不能確認
12 Bad device or component.壞的設備或元件
13 Out of calibration.超出校驗范圍
14-31 Reserved保留事件代碼Event Codes事件代碼Engine / Pump Control發動機/泵控制器Event Code Condition
017 Coolant Overheat冷卻液高溫
043 "Abnormal Battery Charge(Voltage To Power Supply Low)" 電壓異常（電壓低）
050 "Abnormal Battery Charge(Voltage To Power Supply High)" 電壓異常（電壓高）
059 Insufficient Level Of Coolant冷卻液不足
095 Fuel Filter Is Clogged燃油濾芯堵塞
100 Engine Oil Pressure Is Low發動機機油壓力低
119 Fuel Level Is Low燃油油位低
171 Engine Oil Level Is Low發動機機油油位低
179 "Abnormal Battery Charge(Charging Is Abnormal)" 電瓶充電異常
232 Water Separator Draining Demand油水分離器需排水
235 Hydraulic Oil Level Is Low液壓油位低
236 Hydraulic Oil Filter Is Clogged液壓油濾芯堵塞
237 Overload Warning過載警報
272 Air Filter Is Clogged空氣濾芯堵塞
600 Hydraulic Oil Overheat液壓油高溫
862 Special Filter Is Clogged專用濾芯堵塞
863 Automatic Greasing Failure油脂自動注油失敗Event Codes事件代碼Engine Control發動機控制器Event CodeCondition
005 Fuel Filter Restriction Derate燃油濾芯堵塞減額
015 High Engine Coolant Temperature Derate冷卻液高溫減額
017 High Engine Coolant Temperature Warning冷卻液高溫警報
025 High Inlet Air Temperature Derate進氣溫度高減額
027 High Inlet Air Temperature Warning進氣溫度高警報
039 Low Engine Oil Pressure Derate機油壓力低減額
096 High Fuel Pressure燃油壓力高
100 Low Engine Oil Pressure Warning發動機機油壓力低警報
190 Engine Overspeed Warning發動機超速警報
265 User Defined Shutdown用戶自定義熄火挖掘機技術故障與師傅進行溝通交流，官方網站http://www.ccooddee.com修理直撥:0551-64493367 服務專線:13956953738
友情鏈接：
挖掘機維修
| 耐腐蝕泵
| 氣液增壓缸
| 襯氟設備
| 磨粉機
| 撥動開關
| 杭州包裝設計
| uv燈
| 油液監測
| 房車鎖
| 碳化硅廠家
| 聚氨酯泡棉
| 碳纖維拉擠
| 代理記帳
| 轉輪除濕機
| 重慶防火門
| 龍巖鋼閘門廠家
| 凍肉切丁機
| 滑雪場設計
| 直線模組
| 鷹嘴剪
| 氧化鐵紅
| 防爆電動滾筒
| 四川熱軋鋼板
| 全自動點膠機
| 水上滑梯廠
| 管道離心泵
| 廣東護欄廠家
| 渦輪流量計廠
| 電伴熱
| 潔凈工作臺
| 高低溫試驗箱
| 油液在線監測
| iso認證咨詢
掃一掃二維碼 微信咨詢